Rough terrain / 4WD
Dieci Apollo 25.6 Telehandler
Dieci Apollo 25.6
2.5 tonne telehandler, 5.78m lift height, 3.25m forward reach — a compact fixed-boom machine for residential and fit-out sites.
Working height
5.78 m
Power
Diesel
Capacity
2500
Specification sheetDownload Specification sheet
Overview
About the Dieci Apollo 25.6 Telehandler
The Dieci Apollo 25.6 is a compact 2.5 tonne fixed-boom telehandler: 2,500kg maximum capacity, 5.78m maximum lifting height and 3.25m maximum horizontal extension, all on wheels with no outriggers to set. Two steering axles with four planetary reduction gears give three steering modes — four wheel, transversal (crab) and two wheel — so it manoeuvres in tight yards. 5,100kg unladen, 30km/h road speed, 80 L/min hydraulic pump, 12×16.5 tyres.
Where it works
Best-fit jobs and sites
- Loading and placing materials on residential and fit-out sites, yard handling, feeding scaffold and roof levels where a full-size telehandler will not fit.
Good to confirm: Read the load chart at the reach and height being used, not the headline 2,500kg. Diesel engine — outdoor and well-ventilated use. An online listing cannot replace a site assessment, so tell us the job and we will confirm suitability.
Specifications
Full specifications
Grouped for quick scanning — a row appears once its figure is verified for this machine. The manufacturer spec sheet always takes precedence.
Reach & platform1 spec
- Working height
- 5.78 m
Capacity1 spec
- Platform capacity
- 2500
Performance3 specs
- Terrain type
- Rough terrain / 4WD
- Indoor use
- No
- Outdoor use
- Yes
Power & drive2 specs
- Power source
- Diesel
- Drive type
- 4WD
Machine & transport5 specs
- Manufacturer
- Dieci
- Model
- Apollo 25.6
- Machine weight
- 5100
- Customer pickup
- Delivery only
- Delivery
- Quoted by suburb & access
Delivery, access and running
Delivery is quoted by suburb, site access and transport requirements. Tell us the tightest access width on site if the machine must pass through gates, doorways or between structures.
Licence and competency: Non-slewing telehandler rated 2,500kg — under the 3 tonne threshold, so no non-slewing mobile crane high-risk work licence (TLILIC0005) is required in NSW. Verification of competency still applies. Read the load chart at reach before every lift.
Hire period: Hire runs from delivery or pickup until off-hire is confirmed. Rates are quoted for your dates, suburb and machine together; see our hire terms for responsibilities during the hire.
Pre-start checks, every day
Every Equip Hire machine is function-tested before delivery, and every operator still checks the machine before each shift. This is the baseline we use; the machine's own logbook and check sheet govern.
Walk around
- Tyres / tracks, wheels and structure: damage, cracks, leaks
- Scissor stack / boom, pins and hoses: no visible damage or hydraulic leaks
- Decals, capacity plate and rails in place; gates close properly
- Work area: overhead power lines, holes, slopes, other traffic
Power on
- Fuel level, engine oil and coolant
- Ground and platform controls both operate correctly
- Emergency stop and horn work from both stations
Function test
- Raise, lower and drive at low height before working
- Emergency lowering: know where it is and that it works
- Tilt / overload alarms not showing faults
Any fault: tag it out and call us on 0472 721 234. Do not operate a machine with a known fault. Based on manufacturer pre-start requirements and SafeWork NSW guidance.
Before it arrives
- Measure the route, not the door. Every gate, corridor and lift on the way to the work area: handles, hinges, bollards and stored materials all eat clearance.
- Walk the ground. Compacted and trafficable beats "looks firm", so mark soft spots, trenches and services before the machine tracks over them.
- Clear the work zone. Overhead services, sprinkler heads and light fittings at working height; exclusion for people below.
- Delivery space. Room for the truck to stop and unload safely. Tell us about docks, driveways and height limits when you book.
Mistakes we see weekly
- Booking on ceiling height instead of the actual task height. Measure to the work, then add nothing "just in case".
- Quoting the nominal door size instead of the clear opening. An 820 mm door leaf are not 820 mm once the door stop is counted.
- Treating a rough-terrain machine as an indoor unit. The tyres mark floors and the engine can't run enclosed.
- Leaving induction and permit requirements to delivery morning. Shopping centres and managed sites need paperwork before the truck arrives.
Documents
You might also consider
More in this category
Planning guides
Get a quote for the Dieci Apollo 25.6 Telehandler
Tell us the job, the dates and the suburb. We will quote the machine and delivery together.