# Scissor Lift Won’t Start or Lift? Safe Checks Before You Call

> Canonical page: https://equiphire.com.au/scissor-lift-won-t-start-or-lift-safe-checks-before-you-call/. Last updated 2 November 2026.

Most "the machine is dead" calls we take end within two minutes, solved by one of a handful of checks any operator can safely make from outside the machine's covers. Here they are, in the order we ask them on the phone, and the clear line where checking stops and calling starts.

## Won't power on

- Emergency stops: there are two, one at the platform and one at the ground station. Either one pressed disables everything. Twist to release.
- Battery isolator: many machines have a red isolator switch or pull-out key near the ground controls. Off means dead.
- State of charge: a machine left off the charger overnight may simply be flat. Check the charge display; plug in if in doubt. Why overnight charging matters is in charging an electric scissor lift.
- Charger still connected: most machines will not drive while plugged in. Unplug before blaming the machine.

## Powers on but won't drive or lift

- Control station selection: the ground-station key switch selects platform or ground control. In the wrong position, the platform controls do nothing.
- Tilt alarm sounding: the machine is beyond its slope rating and is protecting you. Lower and move to level ground. If the site has no level ground, the machine may be the wrong one for it: see ground conditions for access equipment.
- Overload indicator: over the platform capacity the machine refuses to lift. Count people, tools and materials against the plate.
- Enable triggers: platform controls need the enable trigger or footswitch held while operating, a common one for first-time operators.
- Weather: in strong wind or heavy rain, some machines limit or stop outdoor use by design. The rules are in operating access equipment through Australian weather.

## Charging problems

- The outlet, not the machine: test the outlet with something else. Site power trips overnight more often than chargers fail.
- Leads and connections: fully seated, dry, and not run through a puddle or pinch point.
- Charger indicators: most chargers show a charging light sequence. Note what it shows before calling; it tells us a lot.

## A code on the display

Write the code down exactly as shown, including any letters and the order of flashes. Do not clear it before you call: the code is how we tell a tilt or overload cut-out from a fault that needs a technician. What the common codes mean, and why you record them rather than reset them, is in EWP fault codes: record, stop and call.

## Where checking stops

If those checks do not bring the machine back: stop. Do not open covers, pull fuses, top up fluids or attempt manual overrides other than the emergency lowering procedure you were shown at handover. Note any fault code on the display, keep the machine parked safely, and call 0472 721 234. We will either talk you through a safe reset or get a replacement machine moving: a machine problem on our fleet is ours to fix.

## Prevent the next call

Most of these faults show up in the first minutes of a shift, so a proper pre-start catches them before anyone is at height. The checklist we give customers is in daily EWP pre-start inspection, and who is responsible for which inspection while the machine is on hire is in EWP inspections on hire.

## FAQ

Can I use the emergency lowering if the machine dies at height? Yes, that is what it is for, and it is covered at handover. Use it to bring the platform down safely, then call us before any further use. The wider plan is in EWP rescue planning.

The machine works but something feels wrong. Keep going? No. Odd noises, jerky movement or intermittent controls are early warnings. Park it, call us, and we will decide together.

What should I have ready when I call? The machine's fleet number from the decal, the site address, what the machine was doing when it stopped, any code on the display and the charger light sequence if it is on charge.

---
Markdown copy of https://equiphire.com.au/scissor-lift-won-t-start-or-lift-safe-checks-before-you-call/ (the HTML page is canonical). Generated 2026-11-18T18:06:58+00:00. Index: https://equiphire.com.au/llms.txt
